Buyers Guide to Surge Protected Power Boards

How do surge protected power boards work ?
At first glance a surge protected power board operates like any other Power Board. It shows its ability at that moment when too much voltage gets passed along the transmission line , the surge protected board lets only a ‘safe’ amount through to the connected equipment. The rest it channels into the electrical outlet’s ‘earth’ and safely dissipated into the ground.
When a surge occurs at a certain level above normal voltage, a component built into the surge protected power board becomes conductive and starts to carry the excess electric current back down through the ground wire, so the damaging high voltage doesn’t reach connected equipment. Once the surge ends, that protective component resumes its ‘dormant’ stage of being non-conductive. It’s a bit like an electrical version of a pressure valve.
Australian domestic wiring is designed for a standard voltage of 230–240 volts. If the voltage goes too far above that, it can damage electronic equipment, which usually has many sensitive components. If excess voltage lasts for a very brief time (1–2 nanoseconds) it’s called a spike. If it lasts longer it’s called a surge. Even though a spike or surge can be so brief their duration is measured in nanoseconds, they can still cause damage to sensitive components. It is vitally important to protect sensitive business equipment, Computers, printers, photocopiers etc these items of equipment are sensitive to Surges in voltage.
So what sort of a Surge Protected Board should you Buy ?
Energy absorption/dissipation – This rating, given in joules, tells you how much energy the surge protector can absorb before it fails. A higher number indicates greater protection. Look for a protector that is at least rated at 200 to 400 joules. For better protection, look for a rating of 600 joules or more.
Response time – Surge protectors don’t kick in immediately; there is a very slight delay as they respond to the power surge. A longer response time tells you that your computer (or other equipment) will be exposed to the surge for a greater amount of time. Look for a surge protector that responds in less than Ten nanoseconds.
It is best to look for a Surge protected board with an indicator light that tells you if the protection components are functioning. Eventually the protection component will burn out after continual power surges, but the board will still function as a power connection. Without an indicator light, you have no way of knowing if your protector is still functioning properly.
Other important features may include ?
Building wiring status indicator: Detects potentially dangerous wiring problems in the wall outlet.
Circuit breaker: Protects the surge board from overload by connected devices drawing too much current.
EMI noise filtration: This reduces or eliminates line noise (electrical interference).
Other connections: Surge protected sockets for coaxial cable, modem or Ethernet network, all of which can also conduct high voltage that can damage connected devices.
Outlet spacing: Allows more room for one or more devices that use a transformer block.
Sockets: Check the number of mains power sockets available, usually from four to eight.

<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>

At Tested and True …we come to your work place at a time convenient to you. We can do an assessment of your Electrical Hazards it can be conducted at the same time as we test and tag your Electrical Equipment. We provide a Full Report with recommedations to clear up current Hazards and how to prevent future risks. Call and ask for a quote. 040 7605568 Tested & True ~ test & tag Adelaide uses the very latest in Portable Appliance Testing…The STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and in Calibration. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australiand Standard AS/NZS 3760:2010 ensuring that you get Quality Service at a competitive price. Call Now Mobile 040 7605568

Visit us at or our Newsletter

Peter Hill Manager , Tested & True ~ test & tag Adelaide July 2012

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s