My Safety Switch has tripped… What should I do NOW !?

A Simple step by step guide to fault finding a tripped Safety Switch.

Note: Some types of appliances may cause incidental or nuisance tripping of your Safety Switch or RCD device. Typically Water Heaters, Electric Jugs and Kettles, Steam Irons, Dishwashers, washing Machines, Swimming Pool Equipment, Auto Defrost Refrigerators and Freezers.
Most Important: If your Safety Switch has turned off, it has done so for a reason. It has detected a leak of some electricity. This may be through a faulty appliance or it may be a fault in the house wiring. These instructions will help you find that leak.

1. First try to turn the Safety Switch on.[Marked Residual Current Device]
2. If it stays on then the fault was intermittent or transient and we can do nothing at this stage. Refer to Note above.
3. Think of what you were using at the time.
If the Residual Current Device trips off again, got to point 5.
4. Turn on the Residual Current Device.
5. If it won’t stay on then you will have to unplug all appliances!
This includes any outside power points or power to outbuildings.
6. At this point the Residual Current Device should stay on. [If not you will need to call an Electrician.]
7. If the Residual Current Device stays on then turn the Circuit Breakers on one at a time.
8. When you come to the leaking circuit, the Residual Current Device will turn off.
9. Unplug all appliances that are plugged in to power points that do not work.
Turn the Residual Current Device on. If it won’t stay on then you will have to call an Electrician.
10. If it stays on, then one of the appliances you have unplugged is faulty. Plug the items in, one at a time until you find the faulty one.

Remember Do not fix any Electrical device yourself, give the device to a suitably qualified electrical repair workshop or if under warranty consult with the manufacturer for the possibility of repair under those warranty conditions.
<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
Tested & True ~ test & tag  Adelaide uses the very latest in Portable Appliance Testing…The STC Pro-Logger 2 it can perform static testing class 1,2 & M ,RCD testing, Earth Leakage Detection, 3 phase run testing and logs results as you test. all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and in Calibration. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standards ensuring that you get Quality Service at a competitive price.

Call Now Mobile 040 7605568
Visit us at
www.testedandtrue.com.au
or our Facebook Page at https://web.facebook.com/testedtrue

Peter Hill Manager , Tested & True ~ test & tag Adelaide June 2017

National Coverage through the Safety Services Network (SA State Member)

SSN

|Test and Tag||Lonsdale||Adelaide||South Australia|

Understanding the Danger of Electrical shock

The 2  Major hazards attributed to electrical equipment and wiring are electrical shock and fire. Electrical shock occurs when the body becomes part of the electric circuit, either when a part of your body comes in contact with both of the active component (Active/Neutral)wires of an electrical circuit, or one wire of an energized circuit and the Earth wire (or grounded wire)…., or a foreign conductive object that has become energized by contact with an electrical conductor.

The severity and effects of an electrical shock depend on a number of factors, such as the pathway through the body, the amount of current, the length of time of the exposure, and whether the skin is wet or dry (ie sweat). Water is a great conductor of electricity, allowing current to flow more easily in wet conditions and through wet skin.

240V can kill!The effect of the shock may range from a slight tingle to severe burns to cardiac arrest. The chart below shows the general relationship between the degree of injury and amount of current for a 50-cycle hand-to-foot path of one second’s duration of shock. While reading this chart, keep in mind that most electrical circuits can provide, under normal conditions, up to 20,000 milliamperes of current flow. So only a very small percentage of current leaking to earth can cause harm if touched by your body… as little as 30 milliamperes of current can KILL !!!

Current
Reaction
1 Milliampere Perception level
1-5 Milliamperes Slight shock felt; not painful but disturbing
6-29 Milliamperes Painful shock; “let-go” range
30-150 Milliamperes Extreme pain, respiratory arrest
151-4,300 Milliamperes Ventricular fibrillation
4,300+ Milliamperes Cardiac arrest, severe burns & even death

In addition to the electrical shock hazards, sparks from electrical equipment can serve as an ignition source for flammable or explosive vapors.

Even loss of electrical power can result in extremely hazardous situations. Flammable or toxic vapors may be released as a chemical warms when a refrigerator or freezer fails. Fume hoods may cease to operate, allowing vapors to be released into the work area.  So take care with your electrical equipment and consider all contingencies in the operation of that equipment.

<<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>

Of course the best way is to ensure that your appliances are not hazardous in the first place by ensuring that not dangerous electrical currents are present on the external parts of the appliance. We at Tested & True ~ test & tag come to your work place at a time convenient to you. We can do an assessment of your Electrical Hazards it can be conducted at the same time as we test and tag your Electrical Equipment. We provide a Full Report with recommendations to clear up current Hazards and how to prevent future risks. Call and ask for a quote. 040 7605568

Tested & True ~ test & tag  Adelaide uses the very latest in Portable Appliance Testing…The STC Pro Logger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and in Calibration. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standards ensuring that you get Quality Service at a competitive price.

Call Now Mobile 040 7605568

Visit us at http://www.testedandtrue.com.au located in Lonsdale, South Australia

Peter Hill Manager Tested & True ~ test & tag Manager SA 0407605568 January 2017

National Coverage through the Safety Services Network (SA State Member)

SSN

Peter Hill Manager Tested & True ~ | test & tag | Lonsdale | South Australia |

The Electrical Switchboard your backup defence in electrical safety.

Fuses, Circuit Breakers and Safety Switches

These devices are found in your Switch board understanding these devices and how to use and maintain them will help  your management and understanding of Electrical Safety in the Workplace.

Primary Overload response devices (Fuses & Circuit Breakers)

Fuses and circuit breakers are built to fail in conditions of excess current which can overload the electrical wires in your home. These overloads are often caused by faulty appliances. When an overload occurs, the fuse melts before the wires can overheat, which reduces the risk of fire. Circuit breakers will often trip quicker and more importantly they can be reset to help diagnose and remove faults

  1. Always replace a blown fuse with the correct fuse wire. Never use fuse wire that is heavier than the recommended gauge.
  2. Never use any other type metal or wire.
  3. If fuses keeps blowing, or a circuit breaker keeps tripping, check that your appliances are not faulty.
  4. If fuses continue to blow, or circuit breakers continue to trip after appliances are unplugged, there could be a problem with your wiring. Contact a licensed electrician immediately.

Safety switches and RCD devices

Safety switches or RCD device look similar to circuit breakers and will have a test button to provide a test for the correct earth tripping of the device. The purpose is to they provide extra protection from electric shock. Safety switches monitor the flow of electricity and if any irregularity is detected, the electricity supply is immediately cut off.
Homes with children or backyard workshops should consider installing safety switches to reduce the risk of electrical accidents. It is imperative that commercial premises have them installed and tested regularly.. New homes and Commercial premises are required to have safety switches installed. Licensed electrical contractors can install safety switches in older homes at a reasonable cost. You can also purchase portable safety switches for appliances and extension cords. Useful particularly when using power tools outside ie Electric Lawnmowers, Hedge trimmers, Drills, circular Saws etc  and these portable RCD should also be tested on a regular Basis!

<<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>

Of course the best way is to ensure that your appliances are not hazardous in the first place. Tested & True ~ test & tag comes to your work place at a time convenient to you. We can do an assessment of your Electrical Hazards it can be conducted at the same time as we test and tag your Electrical Equipment. We provide a Full Report with recommendations to clear up current Hazards and how to prevent future risks. Call and ask for a quote. 040 7605568..At Tested and True …we come to your work place at a time convenient to you. We can do an assessment of your Electrical Hazards it can be conducted at the same time as we test and tag your Electrical Equipment. We provide a Full Report with recommendations to clear up current Hazards and how to prevent future risks.  Call Now Mobile 040 7605568

Visit us at http://www.testedandtrue.com.au located in Lonsdale, South Australia

Peter Hill Manager Tested & True ~ test & tag Manager SA 0407605568 January 2017

National Coverage through the Safety Services Network (SA State Member)

SSN

Peter Hill Manager Tested & True ~ | test & tag | Lonsdale | South Australia |

 

So what is tested and what are we looking for when doing a Test and Tag regime?

Many of our clients organise regular test and tagging services simply because it is easier and safer.

A regular program of testing and tagging comprises of: (standard 10/15Amp 3 wire cabled appliance and plugged multi phase equipment)

A visual check to ensure the integrity of the Electrical cord and Appliance construction

  • The Technician looks for Cuts and breaks in appliance and power cables may present as an  electrical hazard.
  • An inspection of the integrity of the appliance housing looking for cracks and holes which may expose personnel to an electrical hazard.

A series of electrical tests are then conducted to detect the unobservable faults not found by the visual inspection process, and forms an integral part of the inspection/testing process.

The equipment is turned off to allow the technician access to the appliance plug. All tests are performed by disconnecting the appliance from the building power and connecting the plug to an insulation tester or a Portable Appliance Test-set built for the purpose of performing the tests automatically and uniformly. These Tests are:

  1. Earthing continuity test: (specifically for metal shrouded appliances) to ensure there is adequate connection between the earth pin on the plug of the appliance and the metal cover shrouding the appliance.
  2. Insulation resistance test: to ensure that no path exists with the appliance/lead for electrical current to transit from the active wires to earth.
  3. Continuity Loop test: to make the sure that the active circuit which powers the appliance has a good solid connection and in no way presents as an electrical hazard.
  4. Polarity Test: (only for items which distribute power: leads, power-boards, adapters etc) to ensure that the wires of an extension cord/power board appear the same order of connection at the plug as the do at the socket end.

Other Equipment Tests Include:

 RCD test to test the tripping time of a RCD to ensure your safety switch or RCD does work properly and switches off in a fault situation quick enough to save personnel from Harm.

3Phase Test: usually high powered workshop and building site equipment with multiple active wire connections (tests performed on 3phase test are similar to that of standard appliance tests outlined above)

Emergency Exit sign test: Tests the ability for an emergency exit sign to stay on when power is off 90 minutes is the expected time, if it fails to reach the expected time then the circuitry/ battery will be in need repair or replacement .

That is it, in a very basic overview if you need to know more please either contact us or contact Safe-Work SA (South Australia) http://www.safework.sa.gov.au/  1300 365 255 or The Workplace Safety Authority in your local area.

<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>

At Tested and True …we come to your work place at a time convenient to you. We can do an assessment of your Electrical Hazards it can be conducted at the same time as we test and tag your Electrical Equipment. We provide a Full Report with recommendations to clear up current Hazards and how to prevent future risks. Call and ask for a quote. 040 7605568 Tested & True ~ test & tag Adelaide uses the very latest in Portable Appliance Testing…The STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEPOO8 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and in Calibration. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standard AS/NZS 3760:2010 ensuring that you get Quality Service at a competitive price. Call Now Mobile 040 7605568

Visit us at http://www.testedandtrue.com.au  also National Coverage through the Safety Services Network (SA State Member)

SSN

Peter Hill Manager Tested & True ~ | test & tag | Lonsdale | South Australia |

 

What Do I need Surge Protector or UPS?

Surge protectors … will protect your equipment from sudden  and dangerous in creases  or spikes in Voltage… They effective in shunting the excess power to earth in the event of the voltage increasing beyond 240 Volts (Australian Single phase appliance line voltage) … so that your equipment safe by making sure only a designated amount of power actually reaches your connected equipment. You can buy them as single-outlet units or multi-outlet power boards.

Surge_protection_board

An Uninterruptible Power Supply ( UPS) has that same qualities , but they provide a back-up power supply for a limited amount of time in case of a blackout or in some more sophisticated units  brown out protection (power goes low <240V) smoothing out any power fluctuations. This means if the power fails you have a good amount of time to save your work on your computer and shut it down normally.

509644

 

Here is the very latest findings from (ACCC) The Choice Website https://www.choice.com.au/electronics-and-technology/computers/computer-accessories/buying-guides/ups-and-surge-protectors

<<<<<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>>

WE can give you advice on choosing an UPS or Surge Power board to suit your Requirements…. and At Tested and True …we come to your work place at a time convenient to you. We can do an assessment of your Electrical Hazards it can be conducted at the same time as we test and tag your Electrical Equipment. We provide a Full Report with recommendations to clear up current Hazards and how to prevent future risks. Call and ask for a quote. 040 7605568 Tested & True ~ test & tag Adelaide uses the very latest in Portable Appliance Testing…The STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP026 in test & tag operations , all our Equipment is in good repair and in Calibration. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standard AS/NZS 3760:2010 ensuring that you get Quality Service at a competitive price. Call Now Mobile 040 7605568

Visit us at http://www.testedandtrue.com.au located in Lonsdale, South Australia

Peter Hill Manager Tested & True ~ test & tag Manager SA 0407605568 May 2016

 

Fire Hazards heaters, clothes dryers & electric blankets

Each winter heaters, electric blankets and tumble dryers cause a large number of house fires in Australia. Have you checked and kept up your maintenance by simply following these valuable tips

Removing hazards and safe use of heaters

  • Never leave heaters unattended. If a fire starts it could spread through your home before you are able to respond.
  • Keep flammable materials at least a metre away from the heater. The majority of house fires are caused by people hanging clothes or towels to dry on or in front of the heater. Clothes, upholstery, curtains and other material that could catch fire should be kept more than a meter from any heater at all times.
  • Make sure portable heaters are secured upright and not left in locations where people or pets could knock them over.
  • Avoid using portable heaters on table tops unless they are secure and designed for that purpose. There is a risk of heat damage to the table top and if it falls off it could damage the heater and start a fire.

Electric heater safety tips

  • Don’t plug electric heaters into powerboards, double adaptors or extension cords with other appliances. Heaters consume large amounts of power and may overload the supply and cause a fire.
  • Before using an electric heater check the condition of the appliance and power cords for obvious damage. If there is damage contact an electrician or the service technician to fix it.

Gas heater safety and correct use

  • Never use gas heaters designed or marked for outdoor use inside. They are a fire risk and can also release toxic gases which can accumulate inside and potentially harm you. Using LPG cylinders indoors to provide fuel for unflued heaters or other gas appliances is dangerous and is not recommended.
  • Unflued heaters must not be used in bedrooms, bathrooms or small rooms that have no permanent ventilation. Toxic gases can build up inside and potentially harm you.
  • Never use your gas oven or stove as a room heater.
  • Always check your gas heater is working correctly. Signs of problems with gas heaters may include difficulty when lighting, yellow flames, unusual smells or noisy or inoperable fans.
  • Regularly service your gas heater according to the manufacturer’s instructions. Always use a licensed gas fitter for this task.

Clothes dryer safety

  • Ensure that the lint filter is cleaned regularly. Lint that has built up can catch fire.
  • Follow manufacturer’s instructions and only place suitable materials into the clothes dryer.

Electric blanket safety

Do you really need them they can be dangerous and not certainly not recommended for use with children (eg Bedwetting) If you really need to use one then every year take it out and give it a thorough check.

  • Electric blankets should be rolled when stored away. Folding an electric blanket can damage element wires within the blanket
  • When using a blanket for the first time after storage, lay it flat on the bed and check for hot spots as it heats up. Only add sheets once you are sure the blanket will operate safely at a maximum temperature.
  • Electric blankets that are not properly maintained can cause fires.
  • Avoid using double adaptors or power boards wherever possible.
  • Older electric blankets might be damaged and may not have the safety features of modern blankets, so consider replacing them.

<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

blog_logo

Tested & True ~ test & tag  Lonsdale We know how to all types of test sensitive electrical equipment like that of a Heaters and Tumble Dryers…We specifically use the STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and up to date. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standards ensuring that you get Quality Service at a competitive price.

Article By Peter Hill… Tested & True ~ test & tag, Lonsdale, South Australia, Contact 0407605568 February 2016 www.testedandtrue.com.au

Who is a competent Person to do Electrical Test & Tag?

 

Competency requirements for those carrying out inspection and testing of electrical equipment

Inspection and testing of electrical equipment must be carried out by a person who has acquired, through training, qualification or experience, the knowledge and skills to carry out the task (i.e. be a ‘competent person’). Inspection and testing of electrical equipment must be carried out by a competent person who has the relevant knowledge, skills and test instruments to carry out the relevant inspection and testing. The person carrying out any testing of electrical equipment should also be competent to interpret the test results of any equipment they use. For example, a person carrying out testing under AS/NZS 3760:2010 must be:

  • a licensed or registered electrician (whichever applies), or
  • in some jurisdictions, a licensed electrical inspector, or
  • a person who has successfully completed a structured training course and been deemed competent in the use of a pass-fail type portable appliance tester and the visual inspection of electrical equipment.

The training should be designed to ensure, so far as is reasonably practicable, that on completion successful participants:

  • can use the relevant test equipment safely and effectively
  • understand electrical risks and appreciate the role that inspection and testing plays in ensuring electrical safety
  • understand AS/NZS 3760:2010 and AS/NZS 3012:2010 (if testing equipment for construction or demolition sites)
  • understand the legal requirements relevant to the work.

Some kinds of electrical testing must only be carried out by a licensed electrician or electrical inspector under local electrical safety laws. For example, testing requiring the dismantling of electrical equipment should only be carried out by a licensed electrician.

Additional or different competencies may be required for more complex kinds of testing outside the scope of AS/NZS 3760:2010.

If in doubt, advice should be obtained from a person qualified and experienced in electrical equipment testing, for example an electrician, electrical contractor, electrical inspector, specialist testing provider or relevant regulator.

<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

blog_logo

Tested & True ~ test & tag  Lonsdale We know how to test sensitive electrical equipment like that of a Surge Power Board and other Surge protected equipment…We specifically use the STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and up to date. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standards ensuring that you get Quality Service at a competitive price.

Article By Peter Hill… Tested & True ~ test & tag, Lonsdale, South Australia, Contact 0407605568 February 2016 www.testedandtrue.com.au