What Do I need Surge Protector or UPS?

Surge protectors … will protect your equipment from sudden  and dangerous in creases  or spikes in Voltage… They effective in shunting the excess power to earth in the event of the voltage increasing beyond 240 Volts (Australian Single phase appliance line voltage) … so that your equipment safe by making sure only a designated amount of power actually reaches your connected equipment. You can buy them as single-outlet units or multi-outlet power boards.

Surge_protection_board

An Uninterruptible Power Supply ( UPS) has that same qualities , but they provide a back-up power supply for a limited amount of time in case of a blackout or in some more sophisticated units  brown out protection (power goes low <240V) smoothing out any power fluctuations. This means if the power fails you have a good amount of time to save your work on your computer and shut it down normally.

509644

 

Here is the very latest findings from (ACCC) The Choice Website https://www.choice.com.au/electronics-and-technology/computers/computer-accessories/buying-guides/ups-and-surge-protectors

<<<<<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>>

WE can give you advice on choosing an UPS or Surge Power board to suit your Requirements…. and At Tested and True …we come to your work place at a time convenient to you. We can do an assessment of your Electrical Hazards it can be conducted at the same time as we test and tag your Electrical Equipment. We provide a Full Report with recommendations to clear up current Hazards and how to prevent future risks. Call and ask for a quote. 040 7605568 Tested & True ~ test & tag Adelaide uses the very latest in Portable Appliance Testing…The STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP026 in test & tag operations , all our Equipment is in good repair and in Calibration. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standard AS/NZS 3760:2010 ensuring that you get Quality Service at a competitive price. Call Now Mobile 040 7605568

Visit us at http://www.testedandtrue.com.au located in Lonsdale, South Australia

Peter Hill Manager Tested & True ~ test & tag Manager SA 0407605568 May 2016

 

Buyers Guide To Surge Power Boards

How do surge protected power boards work ?
At first glance a surge protected power board operates like any other Power Board. It shows its ability at that moment when too much voltage gets passed along the transmission line , the surge protected board lets only a ‘safe’ amount through to the connected equipment. The rest it channels into the electrical outlet’s ‘earth’ and safely dissipated into the ground.
When a surge occurs at a certain level above normal voltage, a component built into the surge protected power board becomes conductive and starts to carry the excess electric current back down through the ground wire, so the damaging high voltage doesn’t reach connected equipment. Once the surge ends, that protective component resumes its ‘dormant’ stage of being non-conductive. It’s a bit like an electrical version of a pressure valve.
Australian domestic wiring is designed for a standard voltage of 230–240 volts. If the voltage goes too far above that, it can damage electronic equipment, which usually has many sensitive components. If excess voltage lasts for a very brief time (1–2 nanoseconds) it’s called a spike. If it lasts longer it’s called a surge. Even though a spike or surge can be so brief their duration is measured in nanoseconds, they can still cause damage to sensitive components. It is vitally important to protect sensitive business equipment, Computers, printers, photocopiers etc these items of equipment are sensitive to Surges in voltage.
Surge_protection_board
So what sort of a Surge Protected Board should you Buy ? Here are the specifications you should consider…Energy absorption/dissipation – This rating, given in joules, tells you how much energy the surge protector can absorb before it fails. A higher number indicates greater protection. Look for a protector that is at least rated at 200 to 400 joules. For better protection, look for a rating of 600 joules or more.
Response time – Surge protectors don’t kick in immediately; there is a very slight delay as they respond to the power surge. A longer response time tells you that your computer (or other equipment) will be exposed to the surge for a greater amount of time. Look for a surge protector that responds in less than Ten nanoseconds.
It is best to look for a Surge protected board with an indicator light that tells you if the protection components are functioning. Eventually the protection component will burn out after continual power surges, but the board will still function as a power connection. Without an indicator light, you have no way of knowing if your protector is still functioning properly.
Other important features may include ?
Building wiring status indicator: Detects potentially dangerous wiring problems in the wall outlet.
Circuit breaker: Protects the surge board from overload by connected devices drawing too much current.
EMI noise filtration: This reduces or eliminates line noise (electrical interference).
Other connections: Surge protected sockets for coaxial cable, modem or Ethernet network, all of which can also conduct high voltage that can damage connected devices.
Outlet spacing: Allows more room for one or more devices that use a transformer block.
Sockets: Check the number of mains power sockets available, usually from four to eight.

<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>

At Tested and True …we come to your work place at a time convenient to you. We can do an assessment of your Electrical Hazards it can be conducted at the same time as we test and tag your Electrical Equipment. We provide a Full Report with recommedations to clear up current Hazards and how to prevent future risks. Call and ask for a quote. 040 7605568 Tested & True ~ test & tag Adelaide uses the very latest in Portable Appliance Testing…The STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and in Calibration. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standard AS/NZS 3760:2010 ensuring that you get Quality Service at a competitive price. Call Now Mobile 040 7605568

Visit us at http://www.testedandtrue.com.au located in Lonsdale, South Australia

Peter Hill Manager Tested & True ~ test & tag Manager SA 0407605568 May 2016

Fixed RCD testing… Why is it important?

At every workplace there is at least one Electrical switch board that is built to divide the power and lighting into manageable circuits feeding, lights, equipment and power points for us to use. Though we may not have an understanding electricity, it is important that you know about the little understood device called the RCD (residual current Device) or sometimes referred to as the Safety Switch that will find amongst the breakers and or fuses in this panel.

An RCD is an electromechanical device,that detects any shunting of electrical power to earth thereby shutting the circuit down in mere milli-seconds, in doing so avoiding electrocution to personnel and possible fire hazards.

Being and Electromechanical device ,it can like any other similar device be prone to failure. As part of a regular testing check, it needs to have a push button test which basically is a test every 6 months to check out the mechanical workings of the RCD of which any body can do. If there are breakers on your Panel that are RCD’s.. the give away is a breaker with a button for testing also on the breaker are the words 30ma RCD… these are the devices that need to be tested monthly by push button. Picture below

IMG_2847

But this is a bit like push button testing a battery smoke alarm it only test the resultant action it doesn’t test the actual detection part of the device.

So periodically you need to have your fixed Main switchboard panel RCD’s tested with a calibrated RCD tester, and if it responds with a shutdown time lag of less than 299 mill-seconds… typical times for most RCD’s are usually are 5-50 milliseconds… here is a table below which will help

TYPE OF ENVIRONMENT IN WHICH EQUIPMENT IS USED
Residual Current Devices (RCDs)
PUSH BUTTON TEST BY USER TEST FOR OPERATING TIME RCD TESTER
FACTORIES, WORKSHOPS, PLACES OF REPAIR, MANUFACTURING,

ASSEMBLY, MAINTENANCE OR FABRICATION.

6 MONTHS 12 MONTHS
LABORATORIES, TEA ROOMS, OFFICE KITCHENS 6 MONTHS 2 YEARS
OFFICE EQUIPMENT WHERE EQUIPMENT OR SUPPLY FLEXIBLE CORD IS SUBJECT TO FLEXING ON NORMAL USE OR IS OPEN TO ABUSE OR IS IN A HOSTILE ENVIRONMENT 6 MONTHS 2 YEARS
OFFICE EQUIPMENT WHERE EQUIPMENT IS NOT SUBJECT TO CONSTANT FLEXING OF THE SUPPLY CORD 6 MONTHS 2 YEARS
NEW EQUIPMENT AND REPAIRED/SERVICED EQUIPMENT PRIOR TO INITIAL INTRODUCTION TO USE, AND AFTER SERVICING PRIOR TO INITIAL INTRODUCTION TO USE, AND AFTER SERVICING

blog_logo

Tested & True ~ test & tag  Lonsdale We know how to test all types of test sensitive electrical equipment like that of a RCDs and Surge Protected devices…We specifically use the STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and up to date. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standards ensuring that you get Quality Service at a competitive price.

Article By Peter Hill… Tested & True ~ test & tag, Lonsdale, South Australia, Contact 0407605568 May 2016 www.testedandtrue.com.au

Fire Hazards heaters, clothes dryers & electric blankets

Each winter heaters, electric blankets and tumble dryers cause a large number of house fires in Australia. Have you checked and kept up your maintenance by simply following these valuable tips

Removing hazards and safe use of heaters

  • Never leave heaters unattended. If a fire starts it could spread through your home before you are able to respond.
  • Keep flammable materials at least a metre away from the heater. The majority of house fires are caused by people hanging clothes or towels to dry on or in front of the heater. Clothes, upholstery, curtains and other material that could catch fire should be kept more than a meter from any heater at all times.
  • Make sure portable heaters are secured upright and not left in locations where people or pets could knock them over.
  • Avoid using portable heaters on table tops unless they are secure and designed for that purpose. There is a risk of heat damage to the table top and if it falls off it could damage the heater and start a fire.

Electric heater safety tips

  • Don’t plug electric heaters into powerboards, double adaptors or extension cords with other appliances. Heaters consume large amounts of power and may overload the supply and cause a fire.
  • Before using an electric heater check the condition of the appliance and power cords for obvious damage. If there is damage contact an electrician or the service technician to fix it.

Gas heater safety and correct use

  • Never use gas heaters designed or marked for outdoor use inside. They are a fire risk and can also release toxic gases which can accumulate inside and potentially harm you. Using LPG cylinders indoors to provide fuel for unflued heaters or other gas appliances is dangerous and is not recommended.
  • Unflued heaters must not be used in bedrooms, bathrooms or small rooms that have no permanent ventilation. Toxic gases can build up inside and potentially harm you.
  • Never use your gas oven or stove as a room heater.
  • Always check your gas heater is working correctly. Signs of problems with gas heaters may include difficulty when lighting, yellow flames, unusual smells or noisy or inoperable fans.
  • Regularly service your gas heater according to the manufacturer’s instructions. Always use a licensed gas fitter for this task.

Clothes dryer safety

  • Ensure that the lint filter is cleaned regularly. Lint that has built up can catch fire.
  • Follow manufacturer’s instructions and only place suitable materials into the clothes dryer.

Electric blanket safety

Do you really need them they can be dangerous and not certainly not recommended for use with children (eg Bedwetting) If you really need to use one then every year take it out and give it a thorough check.

  • Electric blankets should be rolled when stored away. Folding an electric blanket can damage element wires within the blanket
  • When using a blanket for the first time after storage, lay it flat on the bed and check for hot spots as it heats up. Only add sheets once you are sure the blanket will operate safely at a maximum temperature.
  • Electric blankets that are not properly maintained can cause fires.
  • Avoid using double adaptors or power boards wherever possible.
  • Older electric blankets might be damaged and may not have the safety features of modern blankets, so consider replacing them.

<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

blog_logo

Tested & True ~ test & tag  Lonsdale We know how to all types of test sensitive electrical equipment like that of a Heaters and Tumble Dryers…We specifically use the STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and up to date. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standards ensuring that you get Quality Service at a competitive price.

Article By Peter Hill… Tested & True ~ test & tag, Lonsdale, South Australia, Contact 0407605568 February 2016 www.testedandtrue.com.au

Who is a competent Person to do Electrical Test & Tag?

 

Competency requirements for those carrying out inspection and testing of electrical equipment

Inspection and testing of electrical equipment must be carried out by a person who has acquired, through training, qualification or experience, the knowledge and skills to carry out the task (i.e. be a ‘competent person’). Inspection and testing of electrical equipment must be carried out by a competent person who has the relevant knowledge, skills and test instruments to carry out the relevant inspection and testing. The person carrying out any testing of electrical equipment should also be competent to interpret the test results of any equipment they use. For example, a person carrying out testing under AS/NZS 3760:2010 must be:

  • a licensed or registered electrician (whichever applies), or
  • in some jurisdictions, a licensed electrical inspector, or
  • a person who has successfully completed a structured training course and been deemed competent in the use of a pass-fail type portable appliance tester and the visual inspection of electrical equipment.

The training should be designed to ensure, so far as is reasonably practicable, that on completion successful participants:

  • can use the relevant test equipment safely and effectively
  • understand electrical risks and appreciate the role that inspection and testing plays in ensuring electrical safety
  • understand AS/NZS 3760:2010 and AS/NZS 3012:2010 (if testing equipment for construction or demolition sites)
  • understand the legal requirements relevant to the work.

Some kinds of electrical testing must only be carried out by a licensed electrician or electrical inspector under local electrical safety laws. For example, testing requiring the dismantling of electrical equipment should only be carried out by a licensed electrician.

Additional or different competencies may be required for more complex kinds of testing outside the scope of AS/NZS 3760:2010.

If in doubt, advice should be obtained from a person qualified and experienced in electrical equipment testing, for example an electrician, electrical contractor, electrical inspector, specialist testing provider or relevant regulator.

<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

blog_logo

Tested & True ~ test & tag  Lonsdale We know how to test sensitive electrical equipment like that of a Surge Power Board and other Surge protected equipment…We specifically use the STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and up to date. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standards ensuring that you get Quality Service at a competitive price.

Article By Peter Hill… Tested & True ~ test & tag, Lonsdale, South Australia, Contact 0407605568 February 2016 www.testedandtrue.com.au

Buyers Guide to Surge Protected Power Boards

How do surge protected power boards work ?
At first glance a surge protected power board operates like any other Power Board. It shows its ability at that moment when too much voltage gets passed along the transmission line , the surge protected board lets only a ‘safe’ amount through to the connected equipment. The rest it channels into the electrical outlet’s ‘earth’ and safely dissipated into the ground.
When a surge occurs at a certain level above normal voltage, a component built into the surge protected power board becomes conductive and starts to carry the excess electric current back down through the ground wire, so the damaging high voltage doesn’t reach connected equipment. Once the surge ends, that protective component resumes its ‘dormant’ stage of being non-conductive. It’s a bit like an electrical version of a pressure valve.
Australian domestic wiring is designed for a standard voltage of 230–240 volts. If the voltage goes too far above that, it can damage electronic equipment, which usually has many sensitive components. If excess voltage lasts for a very brief time (1–2 nanoseconds) it’s called a spike. If it lasts longer it’s called a surge. Even though a spike or surge can be so brief their duration is measured in nanoseconds, they can still cause damage to sensitive components. It is vitally important to protect sensitive business equipment, Computers, printers, photocopiers etc these items of equipment are sensitive to Surges in voltage.

Surge_protection_board
So what sort of a Surge Protected Board should you Buy ? Here are the specifications you should consider…Energy absorption/dissipation – This rating, given in joules, tells you how much energy the surge protector can absorb before it fails. A higher number indicates greater protection. Look for a protector that is at least rated at 200 to 400 joules. For better protection, look for a rating of 600 joules or more.
Response time – Surge protectors don’t kick in immediately; there is a very slight delay as they respond to the power surge. A longer response time tells you that your computer (or other equipment) will be exposed to the surge for a greater amount of time. Look for a surge protector that responds in less than 15 nanoseconds.
It is best to look for a Surge protected board with an indicator light that tells you if the protection components are functioning. Eventually the protection component will burn out after continual power surges, but the board will still function as a power connection. Without an indicator light, you have no way of knowing if your protector is still functioning properly.
Other important features may include ?
Building wiring status indicator: Detects potentially dangerous wiring problems in the wall outlet.
Circuit breaker: Protects the surge board from overload by connected devices drawing too much current.
EMI noise filtration: This reduces or eliminates line noise (electrical interference).
Other connections: Surge protected sockets for coaxial cable, modem or Ethernet network, all of which can also conduct high voltage that can damage connected devices.
Outlet spacing: Allows more room for one or more devices that use a transformer block.
Sockets: Check the number of mains power sockets available, usually from four to eight.

<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>

Tested & True ~ test & tag  Lonsdale We know how to test sensitive electrical equipment like that of a Surge Power Board and other Surge protected equipment…We specifically use the STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and up to date. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standards ensuring that you get Quality Service at a competitive price.

Article By Peter Hill… Tested & True ~ test & tag, Lonsdale, South Australia, Contact 0407605568 January 2016 www.testedandtrue.com.au

 

Electrical fires & Fire Extinguishers

Electrical fires and Fire Extinguishers

But First a bit about Portable Fire Extinguishers…Basically Fire extinguishers are devices that release chemicals and/or water to put out a fire. They keep small fires from spreading, assist in fighting fires but are only first to the incident appliances until the fire department arrives. Fire extinguishers and on site Fire hoses are designed to provide the user with an appliance to attend a small fire during its initial stage. When deciding to attack a fire, always designate another person to raise the alarm and obtain a back-up fire extinguisher. Portable fire extinguishers should be provided in all buildings.

Types of fire extinguishers and their application

There are basically 5  types of portable fire extinguishers used here  in Australia. They are Water, Foam, Dry Powder, Wet Chemical and Carbon Dioxide. Each type of extinguisher may be rated for one or more classes of fire. In some cases, particular extinguishers are not only considered ineffective against certain classes of fire, they can be dangerous in those circumstances. The Classes of fire are:

CLASS A Paper, Wood, Cardboard

CLASS B Solvents, Paint, Petroleum, Ethanol/methanol

CLASS E Electrical fires(this is the one we are going to concentrate on in this article)

CLASS F Cooking oils and fats

OPERATION

To use the extinguisher, you pull out the safety pin (this metal safety pin prevents the operating lever from closing accidentally) and depress the operating lever. The lever pushes on an actuating rod, which presses the spring-mounted valve down to open up the passage to the nozzle. The bottom of the actuating rod has a sharp point, which pierces the gas cylinder release valve. The proper way to use the extinguisher is to aim it directly at the fuel, rather than the flames themselves, and move the stream with a sweeping motion.

Using an extiguisher

Of the 5 extinguishers types 2 are suitable for Electrical fires they Dry Powder and Carbon Dioxide

Dry Powder

ABE powder consists of mono ammonium phosphate and/or ammonium phosphate. It is effective on Class A: B & E Fires .As well as suppressing the flame in the air, it also melts at a low temperature to form a layer of slag which excludes oxygen from the fuel. For this reason it is effective against class A fires unlike a Rating B:E only extinguisher. ABE powder is the best agent for fires involving multiple classes.

Carbon dioxide

Carbon dioxide is especially effective on electrical fires, Class E Fires, as being a gas; it does not leave any residues which might further harm the damaged equipment. Carbon dioxide (CO2) also works on Classes B and C Fires by displacing the less dense oxygen. This can be problematic in enclosed occupied spaces as we need oxygen too! Although carbon dioxide is exhaled in our own breath, in the high concentrations required to extinguish deep seated fires it is one of the most toxic extinguishing agents used. (Carbon dioxide can also be used on Class A Fires when it is important to avoid water damage, but in this application the gas concentration must usually be maintained longer than is possible with a hand-held extinguisher.)

So as you can see Both of these extinguisher are suitable for Electrical fires but it depends on whether your fighting a fire in a confined space which would make using the Carbon Dioxide Extinguisher out of the question!

Tested & True ~ test & tag  Lonsdale also does fire Extinguisher and smoke Alarm testing to National Standards.. Also we Test and Tag electrical items and we use the very latest in Portable Appliance Testing…The STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and in Calibration. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standards ensuring that you get Quality Service at a competitive price.

Article By Peter Hill… Tested & True ~ test & tag, Lonsdale, South Australia, Contact 0407605568 www.testedandtrue.com.au

 

Uninterruptable Power Supplies (UPS) Buying Advice

Uninterruptable Power Supplies (UPS) Buying Tips

Summers here! … and Summer In Australia means Power Shortages and often leading to Blackouts (no power) or brownouts (low power ie low voltage and current) sometimes these are planned by the Electricity Suppliers to share the extra load during Hot Days… sometimes they occur unplanned because of overloaded or failed equipment either way Your expensive computer or in the case of a business your Server and the data in it could be rendered useless. UPS is the easiest way to protect your hardware and data. For a better and more thorough protection, you need a UPS. It isn’t intended to power you through a blackout though. For that, you would need a generator. Rather, a UPS will let you save your work and power down safely.

A UPS is designed to protect your computer you against such power fluctuations and more importantly, power up your computer even when there is no electricity. Here are a few tips that should help you make a more informed UPS purchasing decision.

  1. Power Outlets

When purchasing a UPS, make sure the power rating is right for your equipment. If you buy one that is rated too low, you might run out of juice before you can power down. Most UPS devices are designed to provide 10 minutes of power. When selecting a UPS, you need to look at the VA rating — or amps multiplied by voltage (240v). The amp rating should be listed on your computer. Add up the VA ratings of everything you will connect to the UPS, then purchase a UPS with a VA rating 20-25% higher. If you are a home PC user, look for a UPS with a 1000-1400 VA rating.

  1. Choose a good length Of Backup time

Don’t expect your UPS to keep your PC running all day. Most UPSes are engineered to provide you a backup time of around 10 to 20 minutes. What they essentially do is save your work when there is a power outage and avoid an abrupt shutdown that could mess up your computer settings. Choose the UPS that meets your backup time demands.

  1. Other features of a UPS

When you are buying a UPS, ask the vendor about more features than just power. This will help you in finding the UPS which has that one additional option that will help you in your buying decision. Of course, the best feature is Automatic Voltage Regulation (AVR) which isolates your PC from voltage fluctuations that lead to computer disturbances. A UPS with AVR conditions the incoming power before being fed to the PC’s Switch Mode Power Supply (SMPS). Most UPSes also automatically initiate a scheduled shutdown sequence when the power is lost, after saving your work, to prevent damage to the computer hardware.

  1. Warranty

Obtain a guarantee before buying a UPS. Undue delays in replacements can affect business. Some vendors offer onsite warranties, where they replace the batteries at your place. If you are planning to use the UPS at work, go for a longer warranty term.

  1. Battery replacement

The general rule is three years. But if you are experiencing low backup times more frequently, you could get the battery replaced immediately if it’s under warranty. If you are facing no problems, expect your battery to work for three years. Its advisable to buy replacement battery cartridges while you are buying the UPS. These cartridges will breathe new life into UPS systems suffering from expired or weak internal batteries.

  1. Power up

Contrary to the myth, its perfectly fine to leave the main switch on even when you are no longer working and the computer is shut down. However, its best to pair your UPS with a voltage stabilizer for additional safety.

  1. Software reporting

The software provided with the UPS is not always accurate with its reports. So don’t listen to it when it says your battery needs to be replaced even though you’ve never experienced low backup times. These faulty reports shouldn’t worry you because they may be trying to get you to purchase the company’s product more frequently (a common problem with print cartridges.) The software is good at its essential function of shutting down the PC properly and saving your work, but you may be the best option to determine whether its time to change the battery.

  1. Tips and tricks

Do not overload the UPS by, for example, connecting external devices like the printer, scanner and the fax machine. NEVER plug a printer into the battery backup system. To optimize the charge of your batteries, you should discharge them completely at least once a month. And lastly, make sure the UPS is properly grounded all the time to prevent any electrical disasters.

  1. Shop around compare specifications against Price..

Standby UPSs are available in the range of 300VA to 500VA for office use, and up to 2KVA to 3KVA for workstations and large servers. Inexpensive standby UPSs ranging in price from $50 to $125 are used by millions of users of personal computers all over the world. Some of them include brands like Belkin, American Power Conversion (APC), Cyber Power, Data Shield, EFI, NCR, SAFE, Pacific Power, Sola and UP Sonic.

Conclusion

Bsically, there are two kinds of UPS systems. The Standby Power System (SPS) and Online UPS System. If you are a home user, go for the relatively cheaper SPS. The price of an online UPS is three to five times that of a standby UPS with the same power rating. For servers, buy an online UPS (online means outgoing power is always drawn from the battery). Expect to pay between $150 and $1,000 for an online UPS. The higher the VA rating, the more you’ll pay. You might also want to consider buying one with advanced-battery features. These features include intelligent-battery management, battery-replacement indicator, and hot-swappable user-replaceable batteries.

Remember

An UPS isn’t intended to power you through a blackout.. For that, you would need a generator. However an UPS is a cost effective way to let you save your work and power down safely.

<<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>

Of course the best way is to ensure that your computer and UPS systems are not hazardous in the first place by ensuring that no dangerous electrical currents are present on the external parts of the appliance or hidden faults inside. We at Tested & True ~ test & tag come to your work place at a time convenient to you. We can do an assessment of your Electrical Hazards it can be conducted at the same time as we test and tag your Electrical Equipment. We provide a Full Report with recommendations to clear up current Hazards and how to prevent future risks. Call and ask for a quote. 040 7605568

Tested & True ~ test & tag  Adelaide uses the very latest in Portable Appliance Testing…The STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and in Calibration. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standards ensuring that you get Quality Service at a competitive price.

Call Now Mobile 040 7605568

Visit us at

www.testedandtrue.com.au

or our Newsletter http://testedtruenewsletter.blogspot.com/

Peter Hill Manager , Tested & True ~ test & tag Lonsdale SA November 2015

Understanding the Danger of Electrical shock

The 2  Major hazards attributed to electrical equipment and wiring are electrical shock and fire. Electrical shock occurs when the body becomes part of the electric circuit, either when a part of your body comes in contact with both of the active component (Active/Neutral)wires of an electrical circuit, or one wire of an energized circuit and the Earth wire (or grounded wire)…., or a foreign conductive object that has become energized by contact with an electrical conductor.

The severity and effects of an electrical shock depend on a number of factors, such as the pathway through the body, the amount of current, the length of time of the exposure, and whether the skin is wet or dry (ie sweat). Water is a great conductor of electricity, allowing current to flow more easily in wet conditions and through wet skin.

240V can kill!The effect of the shock may range from a slight tingle to severe burns to cardiac arrest. The chart below shows the general relationship between the degree of injury and amount of current for a 50-cycle hand-to-foot path of one second’s duration of shock. While reading this chart, keep in mind that most electrical circuits can provide, under normal conditions, up to 20,000 milliamperes of current flow. So only a very small percentage of current leaking to earth can cause harm if touched by your body… as little as 30 milliamperes of current can KILL !!!

Current
Reaction
1 Milliampere Perception level
1-5 Milliamperes Slight shock felt; not painful but disturbing
6-29 Milliamperes Painful shock; “let-go” range
30-150 Milliamperes Extreme pain, respiratory arrest
151-4,300 Milliamperes Ventricular fibrillation
4,300+ Milliamperes Cardiac arrest, severe burns & even death

In addition to the electrical shock hazards, sparks from electrical equipment can serve as an ignition source for flammable or explosive vapors.

Even loss of electrical power can result in extremely hazardous situations. Flammable or toxic vapors may be released as a chemical warms when a refrigerator or freezer fails. Fume hoods may cease to operate, allowing vapors to be released into the work area.  So take care with your electrical equipment and consider all contingencies in the operation of that equipment.

<<<<<<<<<<<<<<<<<<<<<<<<<< 0 >>>>>>>>>>>>>>>>>>>>>>>>>>>

Of course the best way is to ensure that your appliances are not hazardous in the first place by ensuring that not dangerous electrical currents are present on the external parts of the appliance. We at Tested & True ~ test & tag come to your work place at a time convenient to you. We can do an assessment of your Electrical Hazards it can be conducted at the same time as we test and tag your Electrical Equipment. We provide a Full Report with recommendations to clear up current Hazards and how to prevent future risks. Call and ask for a quote. 040 7605568

Tested & True ~ test & tag  Adelaide uses the very latest in Portable Appliance Testing…The STC ProLogger 2 it can perform RCD testing, Earth Leakage Detection and Run Testing all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and in Calibration. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standards ensuring that you get Quality Service at a competitive price.

Call Now Mobile 040 7605568

Visit us at

www.testedandtrue.com.au

or our Newsletter http://testedtruenewsletter.blogspot.com/

Peter Hill Manager , Tested & True ~ test & tag Lonsdale SA October 2015

Home Fire Safety Electrical

In Australia hundreds of fires are caused by potential electrical hazards found in the home apart from fitting a smoke alarm would it not be best that you can reduce these hazards in the first place!

  • Replace or repair damaged or loose electrical cords.
  • Avoid running extension cords across doorways or under carpets.
  • In homes with small children, make sure your home has tamper-resistant (TR) receptacles.
  • Consider having additional circuits or outlets added by a qualified electrician so you do not have to use extension cords.
  • Follow the manufacturer’s instructions for plugging an appliance into a receptacle outlet.
  • Avoid overloading outlets. Plug only one high-wattage appliance into each receptacle outlet at a time.
  • If outlets or switches feel warm, frequent problems with blowing fuses or tripping circuits, or flickering or dimming lights, call a qualified electrician.
  • Place lamps on level surfaces, away from things that can burn and use bulbs that match the lamp’s recommended wattage.
  • Make sure your home has a Safety Switch or Separate RCD breakers for power outlets especially in the kitchen bathroom(s), laundry, basement, and outdoor areas.

We can check your Electrical safety and test your fire Alarms and safety Switches

Tested & True ~ test & tag Adelaide uses the very latest in Portable Appliance Testing…The STC ProLogger 2 it can perform static testing class 1,2 & M RCD testing, Earth Leakage Detection, 3 phase run testing and logs results as you test. all in one neat piece of equipment. On top this all our Technicians are Trained to National Standard UEENEEP008 in test & tag operations by Intertag in Sydney NSW, all our Equipment is in good repair and in Calibration. Most of all we pride ourselves on our Knowledge of OH&S legislation and the current Australian Standards ensuring that you get Quality Service at a competitive price.

Call Now Mobile 040 7605568

Visit us at www.testedandtrue.com.au

or our Newsletter http://testedtruenewsletter.blogspot.com/ … September 2015